Ganesh GT-1640 Engine Lathe, New in 2017 (only 15 hours of use)

All details must be confirmed by the buyer prior to purchase.

A&M Sold this lathe new to an R&D facility which never used the machine.

Featuring:
7-1/2 HP Spindle Motor
Spindle Speeds from 30 - 2,000 RPM
12-Spindle Speed Gear-Ranges for High-Torque
D1-6 Camlock Spindle (A1-6 Optional)
2-1/16" Spindle Bore (52mm)
4-Way Toolpost
23-3/8" Swing in 6.5" Wide Gap
Includes Full-Length Back Splashguard

General Specifications As Per Brochure (must be verified by buyer):

GANESH GT-16 SERIES MACHINE SPECIFICATIONS

Capacity & Dimensions-
Swing over Bed: 16" 410mm
Center height: 8-1/16" 205mm
Swing over Cross Slide: 9-7/16" 240mm
Swing thru Gap: 23-7/16" 595mm
Length of Gap in front of face plate,
D1-6 / A1-6 : 6-1/8" / 6-7/8" 155mm / 175mm optional
Bed casting width/bed casting height: 11-13/16" / 8-1/16" 300mm / 205mm

Spindle-
Spindle Motor Horsepower: 7.5 HP 7.5 HP
Spindle speeds - 12-speeds: 30 - 2000 rpm
Spindle Bore: 2-1/16" 52mm
Spindle Nose: D1-6 (A1-6 optional)
Spindle taper in spindle nose: MT-6 Morse Taper #6

Carriage -
Cross slide travel/Cross slide width: 9" / 7-3/32" 230mm / 180mm
Cross slide lead screw pitch: .200"/rev.
Cross slide resolution per division: 0.001" (on diameters)
Carriage lead screw diameter / pitch: 1-1/4" / 4 TPI 32mm / 6mm pitch
Feed rod dimensions: 7/8" hexagon 23mm hexagon

Compound-
Compound top slide travel/Compound width
4-3/4" / 4-11/32" 120mm / 110mm
Cutting tool height maximum: 1.0" x 1.0" 25mm x 25mm

Tailstock- Engraved with inch / metric quill graduations
Quill diameter: 2-1/8" 54mm
Quill stroke: 4-3/4" 120mm
Quill taper: MT-4 Morse Taper #4
Quill tang drive and drift-slot for tailstock included
Tailstock body set-over adjustment: 1/2" 13mm

Thread Cutting-
Thread cutting range - 40 inch pitches 2 - 56 TPI
Thread cutting range - 53 metric pitches 0.4 - 14mm
Thread cutting range - 32 diametral pitches 4 - 32 D.P. Optional
Thread cutting range - 44 module pitches 0.4 - 7 M.P. Optional

Feeds- (with clutched feed shaft for safety)
Feeds - longitudinal - 40 feeds 0.0012" - 0.0252"/rev. 0.032mm - 0.898mm/rev.
Feeds - cross - 40 feeds 0.0006" - 0.0126"/rev. 0.016mm - 0.449mm/rev.
Feed stop control shaft 4-adjustable automatic feed stops to disengage the
longitudinal feed

Power-
Coolant pump motor: 220vac, 1/8-HP, 3-Phase
Power requirements: 220 vac, 7.5-HP, 3-Phase @ 35-amps

GT-1640 16” X 40” Engine Lathe, LxWxH – 89” x 39” x 48”, 4500# est.
GT-1660 16” X 60” Engine Lathe, LxWxH – 109” x 39” x 48”, 5100# est.