Equipment
CNC Swiss Lathes
CNC Swiss Lathe
TSUGAMI BS-32C - III CNC SWISS LATHE, NEW 2003
Sold

TSUGAMI BS-32C - III CNC SWISS LATHE, NEW 2003

Sell Your Tsugami BS32CIII
CNC Swiss Lathe
Manufacturer:
Tsugami
Model:
BS32CIII
Condition:
Good
Year:
2003
Stock #:
7611396
TSUGAMI BS-32C - III CNC SWISS LATHE New 2003 * IEMCA MAGAZINE BAR LOADER * ***** Super Clean *****

Iemca Boss 432/37 Magazine Loader with 3 channel sets
Guide Bushing Blaster Pump
Chip Conveyor (rear discharge)
Mist Collector (in storage - not used by this owner)
Chipblaster high pressure coolant with 5 different outputs
Double offset drill holder
NSK High Speed Drill (set up for position T5 )
(2) Face Drill / Mill toolholders (never used)
Backworking plate: 3-ID Drills and 3 Rotary Mill / Drill Tools
Over 75 collets and guide bushings
Machine has run Blaser cutting oil and a drum of coolant oil included (no guarantees on how full)
All batteries have recently been replaced

Ours: Only 18,300 Cutting hours, since new (thats less than 1000 hours / year)

Capacity1.25"31.75 mm
ControlCNC (FANUC 18IT)CNC (FANUC 18IT)
Dimensions88" x 60" x 84"H + bar loader88" x 60" x 84"H + bar loader
WeightMachine 6000# + Barlaoder 3500#Machine 6000# + Barlaoder 3500#

All details must be verified by the buyer.

Has only ran oil.

GENERAL SPECIFICATIONS FOR THE TSUGAMI BS32-C MARK III
Control: Fanuc LH-1 (Fanuc 18iTB)
Maximum Bar Diameter: 1 1/4"
Z1-axis Travel (synchronous to "Z2"): 9.75"
Main Spindle:
Spindle Speed: 200 to 7,000 rpm
Indexing: Full C-Axis (.001 degree)
Programmable Servo Axis Designations:
"Z1" main headstock in and out: 9.75"
"T1" OD tool slide up and down: 11.6"
"X1" OD tool slide right and left: 2.28"
"X2" ID tool slide up and down: 8.66"
Auxiliary Slide Motion:
"Z2" ID tool slide in and out:
(Synchronous to "Z1"): 7.88"
Sub-spindle Specifications:
Maximum Diameter: 1 1/4"
Maximum Drill Capacity - mild steel: .472"
Maximum Tap Capacity - mild steel: .393"
Speed Range (serial interface): 200 to 6,000 rpm
Power Rating: 2.7 hp
Sub-spindle Indexing: 5 degree increment
Part Ejection: Front or Rear Ejection
Horsepower of Main Spindle: 7.5 hp
Driven Tool Drive Motor Rating: 1.5 hp
Maximum Speed Cross Tool T10-T12: 200-5,000 rpm
Maximum Speed Cross Tool T13: 120-3,000 rpm
Number of Tool Stations: 6 OD, 5 ID, 3 ID/OD B/W Tools
4 Cross Driven Tools
Tooling Sizes, turning: 5/8" square
Dimensions (apprx):
Machine: 88" x 60" x 84'h
Coolant/Chip Tank
Bar Loader"
Weight (apprx): 6000 lbs.

To the best of our knowledge all details listed below are deemed correct. It is the buyer’s responsibility to confirm all details and we encourage an inspection of the machine(s) and accessories prior to purchase.

We use cookies to improve your experience. Privacy Policy.

Accept